Design Tools shape the restoration only, never a scan (Model Work edits scans). The panel shows on the Design step and in Model Work. Every change is one Undo step.

Design Tools

Form

Brush that adds material to the crown where you drag. Each dab rises as one smooth bump; the margin zone never moves. Click Form again to turn the brush off.

Subtract

Brush that removes material where you drag, the same smooth way. The margin zone never moves. Click Subtract again to turn it off.

Smooth

Brush that evens the surface where you drag, without adding or removing material. It starts at 100 µm strength. Click Smooth again to turn it off.

Move

Puts a handle on the crown: drag it to move the crown. Only the crown moves, never the scans. Confirm keeps the new place; Cancel puts it back.

  1. Click Move (or Rotate).
  2. Drag the handle on the crown. The contact colours follow while you move.
  3. Confirm keeps it; Cancel puts it back. Undo also takes a confirmed move back.

Rotate

Turns the crown with rings in its own frame: about its long axis, and tilted mesiodistally or buccolingually. Confirm or Cancel, as for Move.

Scale

Opens Transform's own Scale on the crown: its handle and its % box. The margin stays on its line. One Undo takes it back.

Show Thin Areas at Margins

Paints purple the crown's wall 0.3 to 0.7 mm above the margin wherever it is thinner than the Margin thickness set in Axis / Spacer (default 0.2 mm), measured straight in to the prepared tooth. Display only: the crown is never changed. On by default; click to turn it off.

Show Thin Areas at Occlusal / Axial Walls

Paints purple every part of the restoration thinner than the Minimum Thickness set in Axis / Spacer (occlusal and axial walls), from 1 mm above the margin up; under that, Show Thin Areas at Margins shows the margin. Display only. On by default once a restoration is proposed; click to turn it off.

Close contacts

One click: every proximal contact of the crowns goes to 20 µm. Open contacts are brought to touch, contacts deeper than 20 µm into a neighbour are pulled back. Needs the neighbouring teeth. Undo restores.

Move Wall

Moves one wall of the crown as a piece: a click picks the whole wall face (mesial, distal, buccal or lingual/palatal); paint or erase to change the area, then In, Out, Up or Down. Each click is one Strength step; holding repeats. The margin stays fixed.

  1. Click Move Wall. Paint region is on.
  2. Click the wall, or drag over the crown to paint the area (Radius sets the brush). Erase rubs part of it out; Clear region starts again.
  3. In moves it inward (less material), Out outward (more material), Up occlusally and Down toward the margin, along the path of draw when one is confirmed.
  4. Done, Esc or Move Wall again leaves the tool.

Morph to opposing

One click: lowers the occlusal surface out of the opposing teeth to 20 µm, never up, and never thinner than 0.5 mm over the preparation. Needs the opposing scan; the occlusal contact colours come on. Undo restores.

Morph contact wall

One click: reshapes only the crown's proximal walls toward each neighbouring tooth, so each contact finishes as a small, centred, tight contact (a tiny red dot in the middle of the contact). Open contacts are brought in, heavy ones relieved. The margin, the inside (fitting surface) and the occlusal surface are not changed. Needs the neighbouring teeth. One Undo per press.

Shape

Sliders that reshape the crown in its own frame: Facial fullness, Mesial and Distal line angle, Incisal embrasures, Length, Cusp height, Taper, Facial shift. Each release is its own Undo step; a change that would make a wall concave or reach into a neighbour is refused. Reset goes back to the crown as it was when Shape opened.

Split Them

Splits a joined design into separate crowns at the contacts. Choose the model in the right column if asked, check each cut plane (Move / Tilt it if needed), then Split. A seam can be cut again later with Re-split.

Connect Them

Joins two models that touch into one model. Tick two models in the right column, then press Connect Them. If they do not touch: Merge anyway keeps the gap (close it with Fill Hole), or change the models.

Virtual Seat

Puts the crown on its working arch at once: the two become one new model, "Virtually seated model", which is the working model for the next tooth. The crown takes the colour of the neighbouring teeth. The originals are hidden, never deleted; one Undo.

Carve Out

Cuts the second model's shape out of the first, for example a housing pocket in a denture. Tick the model to carve, then the model to carve with, then press Carve Out. One Undo restores both.

Radius and Strength

  • RadiusThe brush size, 20 µm to 5 mm (up to 12 mm for Move Wall). Your last setting is kept for the next case.
  • StrengthHow far one brush dab or one Move Wall click moves the surface, 1 to 500 µm. Form, Subtract and Smooth each keep their own; your last setting is kept for the next case.

Move Wall controls

  • Paint regionDrag over the crown to add to the area.
  • EraseDrag over the painted area to rub part of it out.
  • Clear regionRemoves the whole painted area.
  • InInward, less material. One Strength step per click; hold to repeat.
  • OutOutward, more material.
  • UpOcclusally, along the path of draw when one is confirmed.
  • DownToward the margin. The margin line itself never moves.
  • DoneLeaves Move Wall (Esc does the same).